Designed in conjunction with Australia’s leading PA professionals to cater for the needs of multi-source installations. This redesigned unit offers the ability to monitor amplifier status via the colour LCD screen, plus custom labelling of inputs. The A 2711 optional USB & SD card module provides music playback when fitted.
Engineered for professional PA installations, the A 4275C conservatively delivers 125W RMS power. Frequency response extends from 50Hz to 15kHz ±3dB at a total harmonic distortion (THD) of less than 0.5% @ 1kHz. Voice/Vox muting, including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. Operates from 240V ac mains or 24V dc permitting battery backup operation during mains power failure. Output can be 100V line, 70V line or low impedance (4 - 16 Ohm) loads. The circuit includes thermal overload shutdown, over current and overload protection plus fuses on both ac and dc supply rails.
LCD: Indicates input and output levels, amplifier status; including heatsink temperature, overload and over current conditions. 240V ac or 24V dc operation. Also allows custom labelling of input sources via USB keyboard.
Input configuration: Each input can be configured for either balanced microphone or line use. A dip switch is supplied for each input providing the following features: Phantom power on/off, Mic or line, 100mV or 1V, Vox muting on/off (priority)
Three levels of priority: Priority selection is by a dip switch on the rear panel: Input 1 over 2-6, input 2 over 3-6 and input 3 over 4-6.
Overload protection: In the event of an overload, the output current is limited by the internal circuitry, thus reducing the output voltage at the speaker terminals.
Input Limiting: Limits the output to 110V regardless of input level. This prevents dangerously high voltages from damaging the loudspeaker.
A 4573 Alert/evac option board: Generates pre chime, bell, alert and evacuation tones. The alert tone can function continuously, or switch to evac tone after a preset time delay (adjustable 30 seconds to 4.5 minutes). Simply connects to the amplifier internally via the cable provided.
A 2280B Remote volume wall plate: Connects via figure 8 cable to the “remote volume” terminals of the amplifier. Enabling overall volume to be adjusted as required. Features a PCB jumper to reverse the volume control direction. Maximum cable length 100m.
Power Outputs
125 watts RMS
Distortion: < 0.5%, @ 1kHz
Output line: 70V, 100V or 4 - 16Ω
Line output: 600 Ohm balanced, 0dBV
Frequency Response
Mic inputs: 50Hz - 12kHz, -3dB
Line inputs: 50Hz - 15kHz, -3dB
Sensitivity
Mic inputs: 3mV balanced
Line inputs: 100mV-1V
Signal To Noise Ratio (Limiting by-passed)
Mic inputs: > 75dB below rated output
Line inputs: > 81dB below rated output
Output Connectors
Speakers: Screw terminals
Line out: 3 pin XLR, Tape out RCA / send & return RCA
Input Connectors
Inputs: 3 pin XLR balanced or 2 x RCA
24V dc power: Screw terminals
240V ac power: IEC power connector
Muting: PTT via microphone switch contacts or VOX muting
Controls
Mic inputs: Volume
Line inputs: Volume
Bass: ±10dB @ 100Hz
Treble: ±10dB @ 10kHz
Master: Volume
Power: On/off switch
Indicators: Power, fault, all other indicators on LCD
Power Supply: 240V AC or 24V DC
General
Weight: ≈14.5kg
Colour: Black
Fuse Protection: 5A AC , 10A DC
Dimensions: ≈483W x 330D x 88H